Bosch Security and Safety Systems | Indonesia
Product Variants
Product Families
More Content
2-Wire Powered Loop
CTN: B201 | Product No.: F.01U.323.798
- Suitable for use with 2-wire smoke detectors and burglary devices
- Supports up to 20 compatible smoke detectors
- Resets latching devices from the control panel
- Connects to the control panel terminal block with easy-to-install integrated pins
250 in stock
Battery, 12V 7Ah
CTN: D126 | Product No.: 4.998.125.825
- 12 VDC sealed lead‑acid
- Fully rechargeable
- Maintenance‑free
- For use as secondary power source
- Long service life
250 in stock
Door Controller
CTN: B901 | Product No.: F.01U.323.803
- Direct interface to compatible Wiegand card readers
- On-board buzzer output and supervised on-board points
- Request to Exit and Request to Enter inputs that can have a shunt only option
- Four door states: Locked, Unlocked, Secured, Fire Unlock
- SDI2 support as well as SDI compatible
250 in stock
PRODUCT FAMILY
DS7432 Series Eight‑input Remote Modules
- Address up to eight input loops
- Serial dual end-of-line (EOL) wiring with tamper status (DS7432E)
250 in stock
PRODUCT FAMILY
DS7457i Series Single‑zone Input Modules
- Power-limited and supervised input zones
- Compact enough to fit within most back boxes and enclosures
- Address settings through DIP switches
250 in stock
DS7000
Dual multiplex driver
CTN: DS7436 | Product No.: 4.998.126.025
- Provides a two-wire multiplex bus for the connection of up to 120 remote points
250 in stock
PRODUCT FAMILY
DX2010 Series Input Expander
- Up to eight sensor input loops
- Directly connects to the control panel data bus
250 in stock
PRODUCT FAMILY
DX3010 Series Octo‑output Expander
- Up to eight fully programmable and individual operating outputs
- Remotely mount in a D203 enclosure
250 in stock
Enclosure lock and key set
CTN: D101 | Product No.: 4.998.800.200
- Lock and key set fits Bosch enclosures
250 in stock
Ethernet Communication Module
CTN: B426 | Product No.: F.01U.324.383
- Full two-way IP event reporting with remote control panel programming support
- 10/100 Base-T Ethernet communication for IPv6 and IPv4 networks
- NIST-FIPS197 Certified for 128-bit to 256-bit AES Encrypted Line Security
- Plug and Play installation, including UPnP service to enable remote programming behind firewalls
- Advanced configuration by browser, RPS, or A-Link
250 in stock
Mounting plate for D8103 enclosure
CTN: B12 | Product No.: F.01U.260.846
- Easy-to-install standoff locations for mounting supported modules
- Supports B Series control panels in larger enclosures such as the D8103
250 in stock
Plug-in Communicator, Telephone
CTN: B430 | Product No.: F.01U.323.795
- Provides a single telephone line with RJ-45 connection for central station reporting and remote programming
- Easily configured for communications from Remote Programming Software (RPS) or a keypad, eliminating the need for separate configuration
- Easy two-step plug-in installation, troubleshooting, and maintenance
250 in stock
RPS
Programming modem, 2400 baud
CTN: MODEM-KIT-2400B | Product No.: 4.998.800.210
- For programming communications
250 in stock
SDI2 8-Input Expansion Module
CTN: B208 | Product No.: F.01U.397.024
- Programmable input point functions
- Easy to read switch addressing
- 2 interconnect wiring connectors
- Provides eight points
250 in stock
DS7000
Single Multiplex driver
CTN: DS7430 | Product No.: 4.998.800.008
- Provides a two-wire multiplex bus for DS7400Xi Control Panels.
250 in stock
Steel enclosure, medium, grey
CTN: AE1 | Product No.: 4.998.800.323
- Easy-to-install standoff location for mounting supported modules
- Made with cold-rolled steel
- Easy access locations for battery placement
- Optional tamper switch mounting location
250 in stock
Steel enclosure, medium, white
CTN: B10 | Product No.: F.01U.268.495
- Easy-to-install standoff location for mounting supported modules
- Made with cold-rolled steel with a white semi-gloss finish
- Easy access locations for battery placement
- Optional tamper switch mounting location
250 in stock
Transformer plug-in, 16V 40VA
CTN: D1640 | Product No.: 4.998.125.832
- System transformer rated at 16.5 VAC, 40 VA
- Suitable for use on approved UL applications in the USA
250 in stock
Universal plastic enclosure, white
CTN: AE20 | Product No.: 4.998.800.375
- Flexible design accommodates a number of input, output and receiver modules
- Supports modules with circuit boards with either through‑hole or three‑point mounting systems
- Mounts to multiple gang box types
250 in stock
CONETTIX
USB/serial interface module
CTN: DX4010V2 | Product No.: F.01U.080.969
- RS-232/USB connectivity
- Enhanced direct connection for Remote Programming Software (RPS)
- RJ-16 data bus
- Transparent enclosure
- Diagnostic light emitting diodes (LEDs)
- DIP switches for address and bus programming
250 in stock
RADION receiver SD
Wireless SDI2 bus interface
CTN: B810 | Product No.: F.01U.383.394
- Dual internal antennas provide spatial and polar RF signal reception for high reliability
- Cover and wall tamper protection
- Multiple device enrollment options as well as RF diagnostics ensure efficient and effective installation
- Supports supervision of wireless points (504), keyfobs (1000), and repeaters (8)
- External status LEDs
- Detection and reporting of radio frequency interference
250 in stock
DS7000
Splitter for multiplex bus
CTN: DS7425 | Product No.: 4.998.143.563
- One-loop input
- Two-loop output
- Two-wire multiplex bus
250 in stock
Steel enclosure, large, grey
CTN: D8103 | Product No.: 4.998.800.201
- Easy-to-install standoff location for mounting supported modules
- Easy access locations for battery placement
- Optional tamper switch mounting location
250 in stock
Auxiliary power supply module, 2A 12V
CTN: B520 | Product No.: F.01U.172.941
- Provides up to 2 A of 12 V standby current for Fire or Burglar Applications (4 A of Burglary alarm current)
- Supervises up to two 12 V 7-18 Ah batteries independently for up to 36 Ah of capacity
- Provides up to 80 hours of standby time
- Easy-to-read switch addressing
- Uses the Bosch standard TR1850 plug-in transformer
250 in stock
PRODUCT FAMILY
D9127 Series POPIT Modules
- Provides point identification of initiating devices
- Supervises wiring to devices for circuit integrity
- Expands the number of points in the system
- Compact size
- Terminal connections for reliability
- Multiplex technology
- Low installation costs
250 in stock
POPEX
Expansion module
CTN: D8125 | Product No.: F.01U.383.282
- Provides point identification of initiating devices
- Supervises wiring to devices for circuit integrity
- Expands the number of points in the system
- Compact size
- Terminal connections for reliability
250 in stock
POPEX
Expansion module, SDI2
CTN: B299 | Product No.: F.01U.385.673
- Provides point identification for up to 100 connected addressable initiating devices using POPITs
- Supervises wiring to devices for circuit integrity
- Expands the number of points in the system
- Compact size
- Interconnect wiring connectors for easy installation
250 in stock
Metal Enclosure Kit
Metal Enclosure kit w/transformer
CTN: B-ENCL-1 | Product No.: F.01U.322.491
- Compatible for B series control panels
- Easy to install standoff locations for mounting supporting modules
- Installed transformer
250 in stock
POPEX
Octo-output module, form C relays
CTN: D8129 | Product No.: 4.998.800.198
- Programmable relay functions
- Provides eight Form C relays
- 1 A at 30 VDC relay contact rating
- Slide switch configuration
- Allows remote control of relays
- Screw terminal connections
250 in stock
POPEX
Octo-POPIT input module
CTN: D8128D | Product No.: 4.998.800.197
- Provides point identification for initiating devices
- Expands the number of points in the system
- DIP switch programmable
250 in stock
Parallel printer interface module
CTN: D9131A | Product No.: 4.998.800.209
- Prints 80-character, single-line information, such as date, time, event, account number, area number, user ID with text, point # with text and access events
- Connects to a standard parallel printer using a standard parallel cable
250 in stock
Steel enclosure, small, white
CTN: B11 | Product No.: F.01U.262.005
- Easy to install standoff location for mounting supporting modules
- Made with cold-rolled steel with a white matte finish
- Easy access locations for battery placement
- Optional taper switch mounting location
250 in stock
ZONEX retrofit module
CTN: B600 | Product No.: F.01U.383.383
- 3-hole mounting footprint and compact size allow for easy installation
- Provides legacy ZONEX input/output support
- Compact size
- Includes two ZONEX busses allowing for continued ZONEX support on a compatible control panel
250 in stock
Showing of 34 Items
Added to Your Shopping Cart