PRODUCT FAMILY
AVENAR detector 4000
- Highly reliable and accurate thanks to Intelligent Signal Processing (ISP)
- Earliest detection of lightest smoke with dual-optical versions (Dual-Ray technology)
- Monitors environment for electromagnetic influence for fast root-cause analysis
- Automatic and manual address setting
Back box ceiling-mount
Commercial Type No.: FAA-500-BB | Product No.: 4.998.151.302
- Installation in false ceilings
- Easy to install
Back box for damp rooms, surface-mount
Commercial Type No.: FAA-500-SB-H | Product No.: F.01U.510.166
- Damp room sealing for installation in humid areas
- Optional flush or surface cabling
Base extension with damp room sealing
Commercial Type No.: MSC 420 | Product No.: 4.998.113.025
- Damp room sealing for installation in humid areas
- Easy to install
- Surface mounting
Base for Dual-Optical Detector for Ex Ar
Commercial Type No.: FDB201 | Product No.: F.01U.332.583
- Compact and robust design
- High level of resistance to temperature fluctuations, humidity, corrosion and contamination
- Safe insertion of an designation plate
Detector base
Commercial Type No.: FAA-500 | Product No.: 4.998.151.297
- Screw terminals for safe and secure electrical connection
- Easy to install
Detector base with relay
Commercial Type No.: FAA-MSR420 | Product No.: F.01U.508.658
- Equipped with change-over relay
Dual-optical detector, explosive area
Commercial Type No.: OOH740-A9-EX | Product No.: F.01U.332.582
- Compact and robust design
- Earliest detection of lightest smoke with dual-optical or thermal detection
- Highly reliable and accurate
- High level of resistance to temperature fluctuations, humidity, corrosion and contamination
- High resistance to interference
Duct detector housing with base
Commercial Type No.: FAD-420-HS-EN | Product No.: F.01U.029.411
- Use in ventilation systems with air velocities from 1 m/s to 20 m/s
- For the activation of fans, door controls or external display devices an optional Relay Board can be installed
- A clear section on the frosted cover allows observing the alarm LED of the integrated FAD-425-O-R Detector
- Control to prevent unwanted removal of the cover
- Easy installation of the FAD-425-O-R Detector
- Maintains LSN loop functions in the event of wire interruption or short-circuit thanks to two integrated isolators
Dust protection, 10pcs
Commercial Type No.: SSK400 | Product No.: 4.998.035.312
- Protection against dust or other dusty particles before operation
- Easily mounted and removed
PRODUCT FAMILY
FAP‑520 Automatic Fire Detectors LSN improved version
- Modern, ultra-flat design
- Smooth, easily-cleaned detector surface
- Innovative fastening mechanism
- High reliability
- Maintains LSN loop functions in the event of wire interruption or short-circuit thanks to two integrated isolators
- Extended system parameters of improved LSN technology
PRODUCT FAMILY
FAS-420-TM Aspiration smoke detector series LSN improved
- High deceptive alarm immunity with intelligent signal processing
- Innovative fire source identification technology allows the exact location of the fire to be pinpointed by monitoring up to five distinct zones
- Innovative airflow monitoring including single-hole monitoring detects obstruction and breakage
- Installation and commissioning made easy by plug-and-play function
- Preservation of LSN loop functions in the event of wire interruption or short-circuit through two integrated isolators
PRODUCT FAMILY
FAS‑420 Aspiration smoke detector series LSN improved
- High deceptive alarm immunity with intelligent signal processing
- Innovative airflow monitoring including single-hole monitoring detects obstruction and breakage
- Initial set-up made easy by automatic initialization
- Maintains LSN loop functions in the event of wire interruption or short-circuit thanks to two integrated isolators
- SL-versions: Noise reduction to 38 dB(A) by extremely quiet fan and up to 34 dB(A) with additional sound absorber
PRODUCT FAMILY
FCP‑320/FCH‑320 Conventional Automatic Fire Detectors
- High reliability of detection thanks to evaluation electronics
- Active adjustment of the threshold (drift compensation) if the optical sensor becomes dirty
- Activation of a remote external detector alarm display possible
- Mechanical removal lock(can be activated/deactivated)
- Dust-repellent labyrinth and cap construction
PRODUCT FAMILY
FCP‑500 Conventional Automatic Fire Detectors
- Modern, ultra-flat design
- Matches the surrounding decor by using color toning inserts
- Smooth, easily-cleaned detector surface
- Innovative fastening mechanism
- High reliability
PRODUCT FAMILY
FCS-320-TM Conventional aspiration smoke detector series
- High deceptive alarm immunity with intelligent signal processing
- Innovative fire source identification technology allows the exact location of the fire to be pinpointed by monitoring up to five distinct zones
- Innovative airflow monitoring including single-hole monitoring detects obstruction and breakage
- Installation and commissioning made easy by plug-and-play function
- Simple implementation of the pipe system planning through patented suction-reducing film sheets
PRODUCT FAMILY
FCS-320-TP Conventional aspiration smoke detector series
- High deceptive alarm immunity with intelligent signal processing
- Innovative airflow monitoring including single-hole monitoring detects obstruction and breakage
- Initial set-up made easy by automatic initialization
- Easy diagnostics through flash code on the detector module or by using the diagnostic software
- Simple implementation of the pipe system planning through patented suction-reducing film sheets
Flame detector flameproof Ex d, IR3
Commercial Type No.: 016519 | Product No.: F.01U.279.764
- Suitable for explosive areas of the zones 1, 21, 2 and 22 (ATEX and IECEx certified)
- Sensitivity according to EN 54-10 Class 1: 0.33 m² flames at 25m
- Low risk of false alarms due to different IR wavelengths and a combination of filters and signal processing techniques
- Reliable operation, even if the lens is contaminated by a layer of oil, dust, water-vapour, or ice
- Selectable response time
- 2-wire or 4-wire configuration via DIP switch settings
Flame detector, IR3
Commercial Type No.: 016589 | Product No.: F.01U.279.762
- Sensitivity according to EN 54-10 Class 1: 0.33 m² flames at 25m
- Low risk of false alarms due to different IR wavelengths and a combination of filters and signal processing techniques
- Reliable operation, even if the lens is contaminated by a layer of oil, dust, water-vapour, or ice
- Selectable response time
- 2-wire or 4-wire configuration via DIP switch settings
PRODUCT FAMILY
FMX5000 IR Flame detectors
- High degree of immunity against false alarms, e.g. from hot surfaces or sunlight
- A microcontroller monitors the functionality and analyses the recorded data. Faults can be indicated on the detector or on a separate line
- Service interface, history memory
- Connection of remote indicator possible
- 3-channel optic test
Heating element
Commercial Type No.: MH 400 | Product No.: 4.998.025.373
- For applications where condensation is likely
- Power-supplied by panel or separate power supply unit
Housing for concrete ceilings
Commercial Type No.: FAA-500-CB | Product No.: F.01U.508.713
- Installation in concrete ceilings
- Easy to install
Label plate large
Commercial Type No.: TP8 400 | Product No.: 4.998.084.710
- Easy detector marking and identification
- Self-adhesive labels can be used
Label plate small
Commercial Type No.: TP4 400 | Product No.: 4.998.084.709
- Easy detector marking and identification
- Self-adhesive labels can be used
Linear beam detector
Commercial Type No.: FIRERAY3000 | Product No.: F.01U.290.195
- Monitoring range of 5 m to 120 m
- Up to 2 detectors per system controller
- Two pairs of fire and fault relays (one per detector)
- Integral LASER alignment
- Self-alignment during operation
- Remote control unit at eye level for easy installation and programming
- Automatic compensation for contamination
- Control unit with LED and LCD displaying - various operating states
- Adjustable alarm thresholds
- Building shift compensation
Linear beam detector, standalone
Commercial Type No.: FRAY-ONE-EN | Product No.: F.01U.400.533
- Standalone product with integrated control unit
- Auto-Alignment with motorized detector head
- Light Cancellation Technology
- Building Movement Tracking
- Detection range up to 120 m
Linear beam detector, standalone
Commercial Type No.: FRAY-ONE-UL | Product No.: F.01U.400.534
- Integrated control unit
- Auto-Alignment with motorized detector head
- Light Cancellation Technology
- Building Movement Tracking
- Detection range up to 393 ft
Linear heat detector, VdS
Commercial Type No.: FCS-LHD-2EN | Product No.: F.01U.393.476
- Applicable in constricted spaces and under extreme environmental conditions.
- IP 65 rated enclosure
- Minimal maintenance costs through continual self-monitoring of the sensor cable
- Commissioning via built in LCD display
- Rate-of-rise and configurable fixed heat alarm detection
Protective cage
Commercial Type No.: SK 400 | Product No.: 4.998.025.369
- Protection against damage from hits or other heavy impacts
- Easily mounted and removed
Remote indicator
Commercial Type No.: FAA-420-RI-ROW | Product No.: F.01U.289.120
- 360° view, for both wall mount and ceiling mount
- Easy cabling thanks to cable ties bracket and all direction knock-out holes
- Long life and robust construction housing
- Efficient LED
Safety barrier
Commercial Type No.: SB3 | Product No.: 4.998.112.085
- Suitable for applications in hazardous areas
- Input/Output Module included
- Impact-proof and scratch-resistant synthetic material
- Large opening for reuse of existing boreholes
- Screwless connection terminals
Spring for wooden/concrete ceilings
Commercial Type No.: FAA-500-SPRING | Product No.: F.01U.510.028
- For installation in concrete and wooden ceilings
- Easy to install
Trim ring, colored
Commercial Type No.: FAA-500-TR-P | Product No.: 4.998.151.296
- Easy to install
- No additional mounting material needed
Trim ring, white
Commercial Type No.: FAA-500-TR-W | Product No.: 4.998.151.295
- Easy to install
- No additional mounting material needed