Accessory mounting bracket for enclosure
Commercial Type No.: D137 | Product No.: F.01U.020.521
- Mount accessory modules in B8103, D8103, D8108A, and D8109 enclosures.
Attack resistant enclosure, large
Commercial Type No.: D8108A | Product No.: 4.998.125.920
- 18 gauge cold-rolled steel enclosure
- UL Listed for Central Station Fire, Local Fire, and Remote Station Fire applications
Auxiliary power supply module, 2A 12V
Commercial Type No.: B520 | Product No.: F.01U.172.941
- Provides up to 2 A of 12 V standby current for Fire or Burglar Applications (4 A of Burglary alarm current)
- Supervises up to two 12 V 7-18 Ah batteries independently for up to 36 Ah of capacity
- Provides up to 80 hours of standby time
- Easy-to-read switch addressing
- Uses the Bosch standard TR1850 plug-in transformer
PRODUCT FAMILY
D9127 Series POPIT Modules
- Provides point identification of initiating devices
- Supervises wiring to devices for circuit integrity
- Expands the number of points in the system
- Compact size
- Terminal connections for reliability
- Multiplex technology
- Low installation costs
Door Controller
Commercial Type No.: B901 | Product No.: F.01U.323.803
- Direct interface to compatible Wiegand card readers
- On-board buzzer output and supervised on-board points
- Request to Exit and Request to Enter inputs that can have a shunt only option
- Four door states: Locked, Unlocked, Secured, Fire Unlock
- SDI2 support as well as SDI compatible
PRODUCT FAMILY
DS7432 Series Eight‑input Remote Modules
- Address up to eight input loops
- Serial dual end-of-line (EOL) wiring with tamper status (DS7432E)
PRODUCT FAMILY
DS7457i Series Single‑zone Input Modules
- Power-limited and supervised input zones
- Compact enough to fit within most back boxes and enclosures
- Address settings through DIP switches
Dual battery harness
Commercial Type No.: D122 | Product No.: 4.998.800.378
- Used for batteries in parallel
- Slide-on connectors
- Built-in circuit breaker protection
Dual tamper switch
Commercial Type No.: ICP-EZTS | Product No.: F.01U.217.038
- Combination tamper switch senses when the opens and if removed from the wall
- Includes a wire loop that can accommodate additional tamper outputs
Enclosure lock and key set
Commercial Type No.: D101 | Product No.: 4.998.800.200
- Lock and key set fits Bosch enclosures
POPEX
Expansion module, SDI2
Commercial Type No.: B299 | Product No.: F.01U.385.673
- Provides point identification for up to 100 connected addressable initiating devices using POPITs
- Supervises wiring to devices for circuit integrity
- Expands the number of points in the system
- Compact size
- Interconnect wiring connectors for easy installation
Expansion module, SDI2, 8-input
Commercial Type No.: B208 | Product No.: F.01U.397.024
- Programmable input point functions
- Easy to read switch addressing
- 2 interconnect wiring connectors
- Provides eight points
Expansion module, SDI2, 8-output
Commercial Type No.: B308 | Product No.: F.01U.397.025
- Programmable output functions
- Easy to read switch addressing
- Provides eight Form C relays
- 1 A at 5-24 VDC relay contact rating
- Allows remote control of outputs
- Quick modular interconnect wiring connector
Mounting plate, 6 location 3-hole, 5 pcs
Commercial Type No.: D9002-5 | Product No.: F.01U.217.699
- Provides protection and additional mounting options for 3-hole mounted modules
- Mounts in G Series-compatible enclosures
Plug-in Communicator, Telephone
Commercial Type No.: B430 | Product No.: F.01U.414.206
- Provides a single telephone line with RJ-45 connection for central station reporting and remote programming
- Easily configured for communications from Remote Programming Software (RPS) or a keypad, eliminating the need for separate configuration
- Easy two-step plug-in installation, troubleshooting, and maintenance
Steel enclosure, medium, white
Commercial Type No.: B10 | Product No.: F.01U.268.495
- Easy-to-install standoff location for mounting supported modules
- Made with cold-rolled steel with a white semi-gloss finish
- Easy access locations for battery placement
- Optional tamper switch mounting location
Transformer plug-in, 16V 40VA
Commercial Type No.: D1640 | Product No.: 4.998.125.832
- System transformer rated at 16.5 VAC, 40 VA
- Suitable for use on approved UL applications in the USA
Universal enclosure, white
Commercial Type No.: B8103 | Product No.: F.01U.300.149
- Easy-to-install standoff location for mounting supported modules
- Made with cold-rolled steel with a white semi-gloss finish
- Easy access locations for battery placement
- Optional tamper switch mounting location
CONETTIX
USB/serial interface module
Commercial Type No.: DX4010V2 | Product No.: F.01U.080.969
- RS-232/USB connectivity
- Enhanced direct connection for Remote Programming Software (RPS)
- RJ-16 data bus
- Transparent enclosure
- Diagnostic light emitting diodes (LEDs)
- DIP switches for address and bus programming
RADION receiver SD
Wireless SDI2 bus interface
Commercial Type No.: B810 | Product No.: F.01U.383.394
- Dual internal antennas provide spatial and polar RF signal reception for high reliability
- Cover and wall tamper protection
- Multiple device enrollment options as well as RF diagnostics ensure efficient and effective installation
- Supports supervision of wireless points (504), keyfobs (1000), and repeaters (8)
- External status LEDs
- Detection and reporting of radio frequency interference
ZONEX retrofit module
Commercial Type No.: B600 | Product No.: F.01U.383.383
- 3-hole mounting footprint and compact size allow for easy installation
- Provides legacy ZONEX input/output support
- Compact size
- Includes two ZONEX busses allowing for continued ZONEX support on a compatible control panel
PRODUCT FAMILY
DX2010 Series Input Expander
- Up to eight sensor input loops
- Directly connects to the control panel data bus
Ethernet Communication Module
Commercial Type No.: B426 | Product No.: F.01U.324.383
- Full two-way IP event reporting with remote control panel programming support
- 10/100 Base-T Ethernet communication for IPv6 and IPv4 networks
- NIST-FIPS197 Certified for 128-bit to 256-bit AES Encrypted Line Security
- Plug and Play installation, including UPnP service to enable remote programming behind firewalls
- Advanced configuration by browser, RPS, or A-Link
Handheld Multiplex point programmer
Commercial Type No.: D5060 | Product No.: 4.998.800.202
PRODUCT FAMILY
DX3010 Series Octo‑output Expander
- Up to eight fully programmable and individual operating outputs
- Remotely mount in a D203 enclosure
8/16 ZONE EXPANDER TO SUIT CM705B ONLY
Commercial Type No.: CM707B | Product No.: F.01U.275.888
8/16 ZONE INPUT EXPANDER MOD PCB (RS485)
Commercial Type No.: CM704B | Product No.: F.01U.271.515
- LAN or locally powered
- Status and Zone Power LEDs
- Service code pad connection
- Separate tamper input
- Automatic recognition by panel
PRODUCT FAMILY
CM705PB Universal LAN Zone Expander Module
- High security module with anti-substitution protection and resettable fuse protection on power out terminals
- Supports Single, Alarm+Tamper and Split EOL, with up to 15 different EOL Resistor options
- 6 Power Out terminals simplify wiring; outputs are overload and short circuit proof
- Service Code Pad connection point
- LAN Termination Shunt and status indicators included
New Solution
Direct link adapter
Commercial Type No.: IUI-SOL-ADAPTER | Product No.: F.01U.292.966
- File configuration
- Firmware upgrade
- Control panel remote control
PRODUCT FAMILY
Fingerprint Readers
- Separate indicators show door and alarm status; built in sounder provides alarm warning
- Lock output and egress input to simplify wiring, with built in tamper switch
- Haptic feedback enhances user operation
- Adjustable volume control
- Anti replay and anti substitution protection
PRODUCT FAMILY
Internal LAN Proximity Readers
- 40 bit transmission format – 125Khz, with up to 40mm read range
- Lock Output and Egress Input to simplify wiring
- Separate indicators show door and alarm status, with built-in sounder providing alarm warning
- Built-in front and rear tamper protection
- Anti replay and anti-substitution protection
OUTPUT MODULE 4-WAY RELAY (RS485)
Commercial Type No.: CM710B | Product No.: F.01U.271.516
- 4 x Form C relay contacts
- LAN monitored
- Status LED
- Service code pad connection
- Separate tamper input
- Automatic recognition by panel
POWER SUPPLY 5 AMP + 2X BATTCHGR (RS485)
Commercial Type No.: CM723B | Product No.: F.01U.275.894
- 5 Amps total combined output current
- Charge up to 2 x 7.2Ah or 1 x 18Ah standby batteries
- Remotely interrogate power supply status via RAS
- Resettable fuse protected with deep discharge protection built-in
- Easily installed into MW720 or MW730 enclosures
REALTIME CLOCK INTERFACE MODULE (RS485)
Commercial Type No.: CM760B | Product No.: F.01U.275.884
- Accuracy better than =/- 2 minutes / calendar year
- Simple RS485 LAN connection to control panel
- Local low battery fault indicator and dedicated tamper input
- LAN monitored, encrypted data and anti-substitution
- Service keypad connection point included
SOLUTION CONETTIX IP ETHERNET MODULE
Commercial Type No.: CM751B | Product No.: F.01U.271.877
- High security (128bit encryption) replacement for PSTN line
- Remote upload / download over IP and alarm reporting over LAN/WAN
- Operate outputs and areas remotely
- Dynamic and fixed IP address support
- Conettix and CSV-IP reporting formats
SOLUTION LAN P/S 1 AMP+BATTCHGR (RS485)
Commercial Type No.: CM720B | Product No.: F.01U.271.517
- 1 Amp continuous rated; LAN monitored
- Multiple protected power outputs
- Resettable fuse protected
- Pulse battery charger
- AC Fail output, low battery output and low battery indicator
Steel enclosure, large, grey
Commercial Type No.: D8103 | Product No.: 4.998.800.201
- Easy-to-install standoff location for mounting supported modules
- Easy access locations for battery placement
- Optional tamper switch mounting location
- Made with cold-rolled steel with a gray finish